ХЕЛИУМ АНТЕНИ И АКСЕСОАРИ
MikroTik TG-BT5-OUT - An outdoor heavy-duty Bluetooth tag
TG-BT5-OUT : the heavy-duty tag for industrial challenges
This version of our BLE tags comes completely sealed, cast in industrial-grade molds to give it a solid IP69k ingress protection rating. In other words, this tag is dust-tight – nothing gets in, and it is fully protected against close-range high-pressure, high-temperature spray downs. Perfect for industrial telemetry systems or to track all kinds of heavy equipment and materials at a construction site.
Like the indoor version, this tag also supports iBeacon, Eddystone, and MikroTik telemetry formats. There is an NFC encoded MAC address and optional encryption. Unlike the indoor version, the outdoor tag comes with a built-in temperature sensor that can be used for condition monitoring. The ±0.5°C precision can be very useful in cold supply chain logistics.
TG-BT5-OUT features an improved 550 mAH battery that will last around five years (with a sending interval of 1s). It is suitable for strapping to all kinds of surfaces, and it can handle a temperature range of -20°C to 85°C.
PANEL 14 HELIUM - 14 DBI TUNED DIRECTIONAL ANTENNA (EU 868)
The 14dBi Optimised Helium Antenna offers +7% forward Power Transmission compared to alternative non optimised VSWR Antenna designs. The unique 14 dBi Tuned Directional Antenna is both directional and has the additional significant advantage that it can be tilted or moved in the Azimuth direction – unlike all other Omni Directional Antennas. This Antenna focuses all of this RF energy into the forward direction only – in one wide and high beam – typically 30 degrees in Azimuth and Elevation.
Typical applications:
- Where it’s desired to steer /direct the Radiated beam into a large or difficult to reach target area. This is achieved by utilising the unique feature of this Antenna design of being able to tilt or move in the Antenna utilising it’s tillable and rotatable Antenna Mount (supplied) to focus the large beam exactly in the direction required.
- Ideal for mounting on high up Balconies or Tower Blocks where Antennas are blocked from radiating in the rearwards direction.
- Installations located on the coast where transmission to the antenna rear is not required/desired.
- Installations located immediately in front of large hills or building where rear radiation is blocked and therefore not required.
- The flat panel sector Antenna is small ,lightweight and unobtrusive and white in Colour.
Мълниезащита - LIGHTING ARRESTER
The gas lightning arrester is to be mounted on the antenna wire, protects the transceiver from the effects of lightning. Applied fuse - reusable. Withstands up to 10 discharge current of 10 kA, or one of 15 kA. During periodic inspections antenna installation, disconnect the antenna cable from the antenna and the other end connected insulation tester.The flow of voltage to ground should begin >230V
Installation - Lightning arrester end is equiped with clamp the connect grounding cable. The required wire is 4mm copper - with standard yellow-green colours. Wire must be tighten with Crimping pliers for electrical wires designed for this purpose . The other end of the cable has to to be connected to the existing lightning instalation with a resistance to ground below 5 Ω. Measurement is a measure of insulation.
-
- DC Spark-over Voltage@100V/S: - 230V+/-20%
- Impulse Spark-over Voltage@100Vµs:Impulse Spark-over Voltage @1kV/µs:Insulation Resistance GΩ: >1
- Impulse discharge current ( 8/20µs ): 10Times -10kA, 1Time- 15kA
- AC discharge current ( 50 Hz,1s,10 times ): 10A,
- Capacitance PF (1MHz): ≤1. Low capacitance core gas is needed for digital signals. It does not blur the shape of digital pulses and parasitic reflections.
