MaxLink

ML-SFP-RJ45-10G-100 is a 10 Gbps SFP+ copper module with an RJ45 connector for copper cables. It is a MikroTik and Cisco-compatible module. The module's reach for 10G transmission is 100m when using Cat6a/Cat7 cables.

The module supports link speed only 10Gbps!

ML-SFP-RJ45-1G is RJ45 SFP 10/100/1000M copper module, compatible with most Gigabit SFP ports available on various networking devices. Maximum distance range is 100m.

Features:
– Power 8 devices from one supply 12v – 48v
– 8 Port Injector
– 8 LAN and 8 POE ports
– Use with any Ethernet switch
– Optional power supplies from 12v to 48v
– Ideal for IP Cameras, VOIP phone, WiFi

PSBT-6-4P-250 is a 6 port 10/100Mbps PoE switch without management. Automatically detects and powers devices supporting PoE standard 802.3af/at (max. 30 W/port) on ports 1 to 4, on port 1 even supports PoE standard 802.3bt (60 W). Ports 5 and 6 serve as uplinks and do not support PoE. The total budget for powering the connected devices is 65 W using the external 52V/1.25A power adapter included in the package. The switch automatically balances the power for individual ports according to the consumption of the device. The switch can be fixed to the wall.

Port 1 additionally supports the 802.3bt standard, where the output power of up to 60 W is available for the connected device! The switches are now also equipped with a function Watchdog. If the Ethernet link is not detected for about 1 minute and the power supply is active at the same time, the supply voltage will be interrupted and the connected device will be restarted.

Manual mode switch:

Normal "N": The switch powers the device at a distance of max. 100 m. The throughput of the switch per port is 10/100 Mbps.

VLAN: Ports are logically separated from each other, in this mode unwanted broadcast storms can be avoided. The switch powers devices up to 100 m and the throughput per port is 10/100Mbps.

250 m: The switch powers devices up to 250 m with a reduced throughput of 10 Mbps per port.

DATASHEET

POE-BOX4-G is a passive Gigabit PoE injector suitable for powering up to 4 devices. Connectors marked "LAN" connect Ethernet ports without power supply eg switch, to the opposite side of "POE" connect devices using passive PoE. For powering PoE injector uses two pairs of Ethernet cable: 4,5 (positive pole) and 7,8 (negative pole). The power supply is connected via a standard 2.1/5.5mm power connector.

The passive PoE injector can be used in the range of 12 to 57V DC with a max. current of 1000mA / port.

POE-BOX8-G is a passive Gigabit PoE injector suitable for powering up to 8 devices. Connectors marked "LAN" connect Ethernet ports without power supply eg switch, to the opposite side of "POE" connect devices using passive PoE. For powering PoE injector uses two pairs of Ethernet cable: 4,5 (positive pole) and 7,8 (negative pole). The power supply is connected via a standard 2.1/5.5mm power connector or via a special 4-pin terminal block. The passive PoE injector can be used in the range of 12 to 57V DC with a max. current of 1000mA / port.

Ethernet ports without power supply (e.g. switch) are connected to RJ45 connectors marked as "DATA" on one side and devices using power supply via Ethernet cable are connected to the opposite side "POWER + DATA". POE-PAN12 is compatible with active elements using pins 4, 5 (+), pins 7, 8 (-). Especially useful for MikroTik and Ubiquiti networks. Power performance can be optimized according to the devices used and their configuration

DATASHEET

Panel integrating 12 passive PoE injectors into a single 19"/1U panel suitable for powering up to twelve devices. Professional solution for remote powering of many active elements with passive PoE support.

You will achieve a powering centrum by adding this pass-through panel into data cabinet that you can easily connect between the existing switch and the patch panel, which already leads to the powered device (IP camera, IP phone, wireless devices, etc.). Power connectors are in standard size 2.1/5.5 mm and both powering all 12 ports according to the selected input:

    - Mode A: Compatible with active components using 1,2 (-) and 3,6 (+) pins such as IP cameras, IP phones, wireless components, and other components using 802.3af/802.3at power adapters. All 4 pairs are for the data.

    - Mode B: Compatible with active components using 4,5 (-) and 7,8 (+) pins such as Ubiquiti networks, MikroTik and other. All 4 pairs are for the data. 

Attention: It is not possible to combine connection of Ubiquiti 100Mbps products requiring 24V power supply for example: NanoBeam, NSM5 with products requiring 48V power supply due to the different behaviour of Ubiquiti POE port powered by 24 V.

Panel integrating 16 passive PoE injectors into a single 19" / 1U panel suitable for powering up to sixteen devices. Professional solution for remote powering of many active elements with passive PoE support.

Important features

• 19" rackmount design
• 16 ports with passive PoE support
• LED indicator to determine the functional power adapter
• The grounding screw on the rear panel to filter Surge
• Overvoltage protection on each port (650 mA/port)
• Input power connector - standard jack 2.1 / 5.5mm

Ethernet ports without power supply (e.g. switch) are connected to RJ45 connectors marked as "DATA" on one side and devices using power supply via Ethernet cable are connected to the opposite side "POWER + DATA". POE-PAN16 is compatible with active elements using pins 4, 5 (+), pins 7, 8 (-). Especially useful for MikroTik and Ubiquiti networks. Power performance can be optimized according to the devices used and their configuration.

Panel integrating 24 passive PoE injectors into a single 19"/1U panel suitable for powering up to sixteen devices. Professional solution for remote powering of many active elements with passive PoE support.

Ethernet ports without power supply (e.g. switch) are connected to RJ45 connectors marked as "DATA" on one side and devices using power supply via Ethernet cable are connected to the opposite side "POWER + DATA". POE-PAN24 is compatible with active elements using pins 4, 5 (+), pins 7, 8 (-). Especially useful for MikroTik and Ubiquiti networks. Power performance can be optimized according to the devices used and their configuration.