Power Supply Unit, PSU

The FiberPoE connects remote PoE devices and provides data and power using fiber and DC cabling. Optical Data Transport for Outdoor POE Devices. The FiberPoE features an outdoor weatherproof form factor with integrated strain relief management. The FiberPoE allows separate power from standard Ethernet cables or standard terminal block / power cable support. There are three ways to configure the input and output power:

DATA IN(SFP) - Data electronic protected(passive optical signaling)

POWER IN - through terminal block or rj45

SHORT SHIELDED POE CONNECTION TO DEVICE

Panel integrating 16 passive PoE injectors into a single 19"/1U panel suitable for powering up to sixteen devices. Professional solution for remote powering of many active elements with passive PoE support.

You will achieve a powering centrum by adding this pass-through panel into data cabinet that you can easily connect between the existing switch and the patch panel, which already leads to the powered device (IP camera, IP phone, wireless devices, etc.). Power connectors are in standard size 2.1/5.5 mm and both powering all 16 ports according to the selected input:

    - Mode A: Compatible with active components using 1,2 (-) and 3,6 (+) pins such as IP cameras, IP phones, wireless components, and other components using 802.3af/802.3at power adapters. All 4 pairs are for the data.

    - Mode B: Compatible with active components using 4,5 (-) and 7,8 (+) pins such as Ubiquiti networks, MikroTik and other. All 4 pairs are for the data. 

Attention: It is not possible to combine connection of Ubiquiti 100Mbps products requiring 24V power supply for example: NanoBeam, NSM5 with products requiring 48V power supply due to the different behaviour of Ubiquiti POE port powered by 24 V.

MikroTik Gigabit PoE adapter for powering any RouterBOARD over Gigabit Ethernet. Simply connect your power source and then use an ethernet cable to connect the injector to the RouterBOARD device. 

Helps reducing number of wires that lead up the tower. 

For using with any RouterBOARD that supports 9-48V PoE. 

The GPOE has shielded connectors.

Two-level UPS with UPS function, suitable for backup, Wireles or Security systems for external batteries.

Output voltage/current: 27.6/5 + 27.1/0.5

UPS function

• Built-in PFC - Power Factor Corrector (correction of power factor, or also reactive components)
• Universal AC input
• Input polarity protection
• Low battery indication
• Surge protection
• Passive cooling
• PFC switching frequency 67 KHz, PWM 134 KHz
• Dimensions: 199 × 110 × 50 mm
• Weight: 880 g
• DATASHEET

DataSheet

A white power adapter with direct installation into a socket with an output voltage of 5V DC, a maximum current of 2.4A, a total output power of 12W and a USB-C connector. The input plug to the socket is EU type.

DATA SHEET

MikroTik OEM power adapter with standard 5.5 / 2.1mm connector designed to power, for example, LED strips or MikroTik devices with input voltage 12V DC. The power adapter has a maximum power 36W and a maximum output current 3A. A power cord is also included with the power supply.

MikroTik OEM power adapter with standard 5.5 / 2.1mm connector designed to power, for example, PoE panels or MikroTik devices with input voltage 24V DC. The power adapter has a maximum power 48W / 96W and a maximum output current 2A / 4A. A power cord is also included with the power supply.

Low-cost passive PoE base unit for powering passive PoE devices over ethernet. Simply connect your power source to the injector, and then use an ethernet cable to connect the injector to the RouterBOARD device. Helps reducing number of wires that lead up the tower, and in other situations.

For using with RouterBOARDS that support 10-28V PoE powering, input needs to be at least 18V to accomodate any losses in cables.

Захранващ блок, 18 канален, 12V/10A, стабилизиран, предпазител на всеки канал, изходна мощност 145W, размери 320х210х65мм.