CCR1009-7G-1C-1S+1U rackmount, 7x Gigabit Ethernet, 1x Combo port (SFP or Gigabit Ethernet), 1xSFP+ cage, 9 cores x 1.2GHz CPU, 2GB RAM, LCD panel, Dual Power supplies, SmartCard slot, RouterOS L6
Без комутационен чип(switch-chip) - устройството вече разполага само с независими Ethernet портове, всеки с директна връзка към процесора, което позволява да се преодолее предишното споделено ограничение от 1Gbit на switch-chip портовете и да се използва пълният потенциал на процесорната мощ.
Комбо-порт - един софтуерен интерфейс 1Gbit, който има два хардуерни интерфейса - SFP и Gigabit Ethernet порт, позволяващ да използвате този от който имате нужда. Възможно е също да превключвате между двата физически интерфейса в RouterOS. В случай на прекъсване, комбинираният порт осигурява хардуерен fail-over.
Поддръжка на 100Mbps SFP - това е първото ни устройство, което поддържа 100BASE-LX / 100BASE-SX / 100BASE-BX влакнести модули, както и стандартните 1,25G SFP модули.
Повече пропускателна способност - тъй като портовете вече са пряко свързани към процесора, новият CCR1009 може да постигне още по-висока пропускателна способност.
Tile 9 core all port test with combo-port and SFP+
Mode
Configuration
1518 byte
512 byte
64 byte
kpps
Mbps
kpps
Mbps
kpps
Mbps
Bridging
none (fast path)
1,300.4
15,792.1
3,759.4
15,398.5
17,782.8
9,104.8
Bridging
25 bridge filter rules
1,244.4
15,112.0
1,395.3
5,715.1
1,368.1
700.5
Routing
none (fast path)
1,300.4
15,792.1
3,759.4
15,398.5
17,411.2
8,914.5
Routing
25 simple queues
1,300.4
15,792.1
1,925.6
8,195.4
1,977.0
1,328.5
Routing
25 ip filter rules
739.2
8,976.8
793.9
3,378.8
801.8
538.8
All tests are done with Xena Networks specialized test equipment (XenaBay),and done according to RFC2544 (Xena2544)
Max throughput is determined with 30+ second attempts with 0,1% packet loss tolerance in 64, 512, 1518 byte packet sizes
Values in Italic indicate that max throughput was reached without maxing out CPU, but because board interface configuration was maxed out
Test results show device maximum performance, and are reached using mentioned hardware and software configuration, different configurations most likely will result in lower results.
S-35/53LC20D is a pair of SFP transceivers, the S-35LC20D is a 1.25G Single Mode optical SFP module with a LC connector, T1310nm/R1550nm, which works for connections up to 20km and supports DDM. The S-53LC20D is a 1.25G Single Mode optical SFP transeiver with an LC connector,T1550nm/R1310nm, which works for connections up to 20km and supports DDM.
Units are tested and compatible with RB260GS, RB2011LS, RB2011LS-IN, RB2011UAS-IN, RB2011UAS-RM, RB2011UAS-2HnD, RB2011UAS-2HnD-IN CCR1036-12G-4S. Units are compatible with non-MikroTik SFP devices as well.
S+DA0001- DAC Еднометров кабел за директна връзка между две SFP или SFP+устройства, примерно два рутера от CCR или CRS сериите.
This is highly cost-effective way to connect two SFP/SFP+ devices (for example two units of CCR1036-8G-2S+) for very short distances, within racks and across adjacent racks. They provide a low cost, low power and low latency interconnect solution for 10-Gigabit Ethernet, Fiber Channel and other industry standards, and are direct attached compliant and fully conform to the SFP+ MSA specifications.
S+DA0003 - DAC Триметров кабел за директна връзка между две SFP или SFP+устройства, примерно два рутера от CCR или CRS сериите.
This is highly cost-effective way to connect two SFP/SFP+ devices (for example two units of CCR1036-8G-2S+) for very short distances, within racks and across adjacent racks. They provide a low cost, low power and low latency interconnect solution for 10-Gigabit Ethernet, Fiber Channel and other industry standards, and are direct attached compliant and fully conform to the SFP+ MSA specifications.
S-85DLC05D is a 1.25G SFP transceiver with a 850nm Dual LC connector, for up to 550 meter Multi Mode fiber connection, with DDM Units are tested and compatible with RB260GS, RB2011LS, RB2011LS-IN, RB2011UAS-IN, RB2011UAS-RM, RB2011UAS-2HnD, RB2011UAS-2HnD-IN and CCR1036-12G-4S. Units are compatible with non-MikroTik SFP devices as well.
S-RJ01 is RJ45 SFP 10/100/1000M copper module, compatible with most Gigabit SFP ports available on various networking devices. Shipped with CCR1016-12S-1S+, by popular demand is now also available for purchase separately.
Bidirectional SFP+ 10G module kit. Kit contains two SFP+ modules that can be used as pair to achieve operating data rate up to 10Gbps for distances up to 10km on single optical cable.
S+RJ10r2 е уникален модул предлагащ високоскоростна свързаност на базата на добре познатите мрежови кабели с усукани двойки и устройства с SFP+ порт. Всяко MikroTik устройство с SFP+ порт и активно охлаждане може да се използва без инсталиране на оптична мрежа, просто включете S+RJ10 и скоростта на вашата мрежа може да се увеличи до 10Gbps, правейки я готова за следващата генерация на RJ45 хардуер. S+RJ10се поддържа и от устройства с пасивно охлаждане, но може да е нужно допълнително охлаждане.
Подобрения във версия 2:We have improved S+RJ10 hardware and firmware. List of improvements:
- Jumbo frames up to 10218 Bytes are now supported; - Link speed reporting is fixed - actual link speed in the interface menu is listed. Previously 100M/1G/2.5G/5G link speeds were not reported correctly; - DDM monitoring (Supply Voltage, Module temperature) is now supported.
All units that we ship now are from new HW revision. You can distinguish new HW revision by "/r2" at the end of the serial number.