Interfaces and Accessories
1.25G SFP transceiver, DDM, 850nm, 550m
S-85DLC05D is a 1.25G SFP transceiver with a 850nm Dual LC connector, for up to 550 meter Multi Mode fiber connection, with DDM Units are tested and compatible with RB260GS, RB2011LS, RB2011LS-IN, RB2011UAS-IN, RB2011UAS-RM, RB2011UAS-2HnD, RB2011UAS-2HnD-IN and CCR1036-12G-4S. Units are compatible with non-MikroTik SFP devices as well.
10G SFP+ Outdoor -40°C, SM, 1310nm, 10km, 2x LC, DDM, Cisco compatible - ML-S+31Dout-10
ML-S+31Dout-10 is a singlemode 10G SFP+ module with 1310nm wave length and 2 LC connectors for link at distance up to 10km. Module is "cisco compatible", so it is compatible with almost all active devices. The advantage of this product is higher frost resistance and its operating temperature is set deep under frost point to -40 to 70°C. The module is ideal for installation in outdoor microwave devices.
ACSMAUFL - U.fl-SMA female pigtail
U.fl-SMA female pigtail, that can be used to connect your LTE card to an external antenna if you are using wAP R kit (there are special openings in the enclosure of the wAP R, designed for these pigtails)
Flex Guide 50cm
A super low loss 50cm long RPSMA cable for superior connection quality, suited for indoor and outdoor use, this cable provides superior matching and loss values.
The name of this cable comes from combining the words “flexible” and “waveguide”, to denote the high end features of this product.
The inner conductor is silver plated copper, and both connectors are soldered, not crimped, for the best possible signal quality. Ideally suited for our BaseBox and other products with RPSMA connectors, and works with most antennas.
GPOE - Gigabit POE Injector Mikrotik
MikroTik Gigabit PoE adapter for powering any RouterBOARD over Gigabit Ethernet. Simply connect your power source and then use an ethernet cable to connect the injector to the RouterBOARD device.
Helps reducing number of wires that lead up the tower.
For using with any RouterBOARD that supports 9-48V PoE.
The GPOE has shielded connectors.
K-79 - RB5009 rackmount kit
With this kit you can mount up to four RB5009UG+S+IN routers in a single 1U rackmount space! No more server-room-Tetris, just pure productivity.
MikroTik GESP+POE-IN
Classic MikroTik GESP surge protector and a brand new device – the GESP+POE-IN, a passive PoE injector with surge protection. Together these two devices offer maximum security and peace of mind.
Here’s what a typical use-case would be like. You have a mast with some antennas. And some switches on the ground. Put the GESP surge protector up there. It comes sealed inside a new and improved IP67 weatherproof enclosure. Your antennas are now safe during a lightning storm. Now add the GESP+POE-IN injector below the mast - to protect the switches and to power the antennas.
Don’t forget about the grounding wire! Secure it to the rackmount, mast, or any other structure that is connected to the ground. For maximum protection, you should use a surge protector on both ends of long cables. These small devices can make all the difference when it comes to lightning strikes or static build-up. The GESP units can usually absorb multiple impacts, but make sure to check their condition after each surge. For attachment of GESP units, we recommend using PVC zip ties. Just don’t make it too tight.You know what they say – hope for the best, prepare for the worst. This small investment can save lots of time and money, so why risk it? Grab a GESP & GESP+POE-IN and put your mind at ease!
DATA SHEET
MikroTik RBPOE - Passive POE Base Unit
Low-cost passive PoE base unit for powering passive PoE devices over ethernet. Simply connect your power source to the injector, and then use an ethernet cable to connect the injector to the RouterBOARD device. Helps reducing number of wires that lead up the tower, and in other situations.
For using with RouterBOARDS that support 10-28V PoE powering, input needs to be at least 18V to accomodate any losses in cables.
MikroTik S+RJ10 r2 - 6-speed RJ-45 module for up to 10 Gbps
S+RJ10 r2 unique module opens up a whole world of high speed connectivity possibilities, offering up to 10 Gbps speeds over regular familiar twisted-pair cables in your existing products that have SFP+ ports. Any MikroTik device with active cooling that has SFP+ ports can now be used without installing any optical fiber, just plug the S+RJ10 and your network can be upgraded to 10 Gbps, making it ready for the next generation of RJ45 hardware.
S+RJ10 module is supported also on devices with passive cooling, but may require an extra cooling.
We have improved S+RJ10 hardware and firmware. List of improvements:
- Jumbo frames up to 10218 Bytes are now supported;
- Link speed reporting is fixed - actual link speed in the interface menu is listed. Previously 100M/1G/2.5G/5G link speeds were not reported correctly;
- DDM monitoring (Supply Voltage, Module temperature) is now supported.
MikroTik S-RJ01 - RJ45 SFP Copper Module
S-RJ01 is RJ45 SFP 10/100/1000M copper module, compatible with most Gigabit SFP ports available on various networking devices. Shipped with CCR1016-12S-1S+, by popular demand is now also available for purchase separately.
