Fiber Optic Routers and Switches

The CRS328-4C-20S-4S+RM is a 28 independent port switch with a combo group. This device has twenty SFP ports, four SFP+ ports for 10G modules and four combo ports, where you can choose to use SFP or RJ45 ports from the combo group. These ports can also be software selected, so if you have plugged in all eight cables, you can use scripting, to decide which four combo ports will be active.

The device comes in a 1U rackmount case with two 100-240 V power supplies with failover functionality. A RJ45 console port is available for management and debugging, and a mode button can be customised to execute any RouterOS commands.

The device has a “Dual boot” feature that allows you to choose between two operating systems - RouterOS or SwOS.

DATA SHEET

QUICK GUIDE

CRS518-16XS-2XQ - With 2x 100 Gigabit QSFP28 ports and 16x 25 Gigabit SFP28 ports, this is the perfect cost-effective addition to any enterprise network or data center. And with dual-redundant hot-swappable power supplies and fans, you won’t have to worry about unnecessary downtime.

At the top, you could place two flagship CCR2216 routers to provide the main connectivity and routing. Then a blazing-fast 100 Gigabit connection leads to three CRS518 distribution level switches. This is where all the magic happens. The CRS518 switches connect every access level device to the main network, deal with traffic filtering, and network policy enforcement. And they handle all that with grace and dignity – thanks to the fantastic Marvell Prestera Aldrin2 switch-chip. The same chip you’ve seen in our flagship CCR2216 that did wonders with L3 Hardware Offloading.

The 25-gigabit ports are backward compatible with 10 Gigabit and 1 Gigabit SFP devices. Mix and match as you need! The two hot-swap power supplies support a high input voltage range: 100-240V. The board itself uses up to 45W of power, while the total maximum power consumption goes up to 77W with all the attachments. It can be a bit more power-hungry than the CRS504, but you would be too if you had 16x 25-Gigabit ports, wouldn’t you?

Nothing can stop this switch: it supports VLAN (802.1Q, 802.1ad), L3 hardware offloaded routing, ACL, LACP, MLAG, Jumbo frames, IGMP/MLD snooping, and so on. Keep your RouterOS up to date and enjoy the real power of CRS!

DATA SHEET

USW-Aggregation is an eight-port, Layer 2 switch that supports 10G SFP+ connections, and is equipped with a fanless cooling system.
Managed with the UniFi Network application: Version 5.14.12 and later

• • (8) 10G SFP+ ports
  • Switching capacity: 160 Gbps
  • 1.3" LCM color touchscreen with AR switch management
  • DATA SHEET
  • INSTALL GUIDE

USW-Aggregation-Pro is a fully manageable L3 switch in a 19" rackmount chassis with 4× SFP28 (supporting 1 G / 10 G / 25 Gbps) and 28× SFP+ (1 G / 10 Gbps support) ports: With a 1.3" touch screen, you can instantly see the most important information such as error conditions, warnings, port statistics, power consumption of connected devices, network load and more. USW-Aggregation-Pro is managed using the UniFi Controller or a mobile application, which allows you to easily create, scale and monitor your corporate network.

• (28) 1G / 10Gbps (SFP+)
• (4) 1G / 10G / 25Gbps (SFP28) - speed on all 4 ports is limited by the slowest of them, or mix. 1G and 10G modules
• 760 Gbps switching capacity
• Touch screen
• Backup power via SmartPower RPS connector
• Supported in UniFi Controller from version 6.1.25 
• DATA SHEET