MikroTik
161
продукти
Продукти
MikroTik Wireless Wire Cube Pro - CubeG-5ac60aypair
Wireless Wire Cube Pro е преконфигуриран комплект от две устройства Cube 60Pro. Wireless Wire Cube Pro ви позволява да установявате ултра бързи връзки от точка до точка на разстояния до 1 км. И това не е всичко – добавихме поддръжка на Channel 5*, така че можете да достигнете дори по-големи разстояния, ако е необходимо. В нашите тестове Cube 60Pro лесно поддържаше надеждна връзка над 2,4 км.
Забравете за прекъсванията с автоматичната 5 GHz резервна връзка(backup connection) - 60 GHz честотен обхват не се влияе от зашумения безжичен спектър и предлага висока скорост и капацитет. Но понякога може да се затрудни при лоши метеорологични условия. Ето защо и двете устройства Cube 60Pro разполагат с автоматичн 5 GHz бекъп.
Повече издръжливост, по-малко нежелано внимание - кутията разполага със здрава метална основа – за по-добри опции за монтаж и охлаждане. Форм-факторът Cube произтича от чистата практичност: той е издръжлив, ненатрапчив и компактен.
MikroTik CRS518-16XS-2XQ
CRS518-16XS-2XQ - With 2x 100 Gigabit QSFP28 ports and 16x 25 Gigabit SFP28 ports, this is the perfect cost-effective addition to any enterprise network or data center. And with dual-redundant hot-swappable power supplies and fans, you won’t have to worry about unnecessary downtime.
At the top, you could place two flagship CCR2216 routers to provide the main connectivity and routing. Then a blazing-fast 100 Gigabit connection leads to three CRS518 distribution level switches. This is where all the magic happens. The CRS518 switches connect every access level device to the main network, deal with traffic filtering, and network policy enforcement. And they handle all that with grace and dignity – thanks to the fantastic Marvell Prestera Aldrin2 switch-chip. The same chip you’ve seen in our flagship CCR2216 that did wonders with L3 Hardware Offloading.
The 25-gigabit ports are backward compatible with 10 Gigabit and 1 Gigabit SFP devices. Mix and match as you need! The two hot-swap power supplies support a high input voltage range: 100-240V. The board itself uses up to 45W of power, while the total maximum power consumption goes up to 77W with all the attachments. It can be a bit more power-hungry than the CRS504, but you would be too if you had 16x 25-Gigabit ports, wouldn’t you?
Nothing can stop this switch: it supports VLAN (802.1Q, 802.1ad), L3 hardware offloaded routing, ACL, LACP, MLAG, Jumbo frames, IGMP/MLD snooping, and so on. Keep your RouterOS up to date and enjoy the real power of CRS!
MikroTik hAP ax2 - C52iG-5HaxD2HaxD-TC - НА СКЛАД!
A Wi-Fi6 version of the legendary hAP ac². With PoE-in and PoE-out, much faster wireless, more RAM, and a modern CPU. Amazing performance and value!
MikroTik CSS610-8P-2S+IN
CSS610-8P-2S+IN е MikroTik ПоЕ суич с два SFP+ порта за 10 Gigabit оптична свързаност и осем Gigabit Ethernet порта с 802.3af/at PoE-out.
Той се предлага с леката SwOS, която е лесна за конфигуриране от вашия уеб браузър. Той ви дава цялата основна функционалност за управляем суич и още: port-to-port forwarding, broadcast storm control, apply MAC filters, configure VLANs, mirror traffic, apply bandwidth limitations, and even adjust some MAC and IP header fields.
But the real blessing is the combination of SFP+ and PoE-out Ethernet ports. With this setup, you can do all kinds of things on a tight budget. CSS610 has an impressive total PoE-out budget of 140 W, so you can use even in the most intense scenarios – like hotels, conference halls, or call centers! Use the PoE-out ports to connect the IP-phones while the SFP+ ports connect your primary server to the ISP. Or power a bunch of network cameras and instantly upload the footage to the cloud. And manage a cluster of wireless access points at the same time. Also, scalability is no longer a problem. With our pricing, you can afford a switch on every floor!
MikroTik RB5009UPr+S+IN - PoE Рутер
RB5009UPr+S+IN има всички предимства на предишния модел: Gigabit Ethernet, 2.5 Gigabit Ethernet и 10 Gigabit SFP+ оптичен порт. Има скоростта, силата и издръжливостта. Но този път добавихме PoE-in & PoE-out на всичките осем Ethernet порта. В комбинация с 2-щифтов конектор и DC жак, вие получавате 10 отделни начина на захранване. Всички опции за захранване поддържат широк диапазон на напрежение от 24 – 57 V. Въпреки това, не можете да смесвате напреженията. Ако използвате PoE изход за захранване на други устройства, RB5009UPr ще избере източника с най-високо напрежение (DC жак или 2-пинов конектор), за да ги захранва. Всеки PoE-out порт може да достави до 25 W мощност, но общата отдавана мощност чрез PoE е ограничена до 130 W. Може ръчно да зададете/ограничите максималната налична мощност според изопзвания източник на захранване.
И така, какво точно се случва, ако има проблем с един от източниците на захранване? Ето един бърз пример: имате 24V на DC жака, 48V на 2-пиновия конектор и 57V на PoE входа. Самата рутер се захранва от входа с най-високо напрежение – PoE-in. Ако има проблем, RB5009 ще се върне към второто най-високо напрежение - 2-пиновия конектор. И ако това не успее – има опция за 24V на DC жака. От друга страна, PoE устройствата захранени RB5009UPr ще черпят енергия от 48V източник на 2-пиновия конектор, ако това не успее – 24V на DC жака влиза в действие. Рутера винаги ще запазва 20 вата за самозахранване. Ако няма достатъчно мощност за всички изходни PoE портове, ще започне да деактивира тези с най-нисък приоритет. Можете да зададете приоритета на порта ръчно.
MikroTik CRS310-1G-5S-4S+IN
This switch is an indoor variation of the prominent netFiber 9 switch – used by many small and medium ISPs for reliable 10 Gigabit fibre connections stretching over a 100 meters. With five 1G SFP ports, four 10G SFP+ ports, and an additional Gigabit Ethernet port, this is the perfect upgrade for existing CRS212 setups. You’re getting the modern ARM v7 CPU, 256 MB of RAM, and better cooling. The new Marvell switch-chips bring phenomenal performance to the table!
The Gigabit Ethernet port has a direct connection to the switch chip – so you can enjoy full gigabit speed there. And it supports PoE-in, giving you an additional powering option in tricky spots.
You can mount this switch in a standard 1U rack to keep everything organized. And it has all the power you would expect from a rackmount device: CRS310 supports hardware offloaded VLAN- filtering. And even some hardware offloaded Layer-3 routing.
CRS310-1G-5S-4S+IN is a fantastic tool for anyone working with indoor connections over 100 meters while keeping data loss and ping low. Optical fiber can be a great alternative to copper if you are worried about electromagnetic interference, tampering or eavesdropping.
MikroTik GPeR-IP67-Case
IP68 външна кутия за GPeR - Sturdy and affordable outdoor enclosure for GPeR units. It can be easily mounted on walls and poles. Despite the name, meticulous testing revealed that in real life the enclosure has an IP68 rating with protection from immersion in water, as well as protection from dust. Get an outdoor enclosure for the GPeR to safely extend Ethernet network in mines, caves, maintenance shafts or outdoors.
MikroTik GPeR - Gigabit Passive Ethernet Repeater
The GPeR unit allows to extend Ethernet cable by additional hop (< 100 - 150 m to regular network devices, and up to 210 m to another GPeR unit) up to 1,500 m.
Handy for highrise buildings, multi-apartment buildings, with many floors and sections, where very long Ethernet cables might be a problem.
Maximum allowed length of CAT6 Ethernet cable between GPeR and power source/router is up to 100 m (depending on cable quality, high quality - up to 150 m).
Maximum allowed distance of CAT6 Ethernet cable between two GPeR devices is up to 210 m (depending on cable quality).
In case if the destination device does not support PoE-in powering, the PoE Passthrough can be disabled by manually removing all jumpers.
MikroTik GESP+POE-IN
Classic MikroTik GESP surge protector and a brand new device – the GESP+POE-IN, a passive PoE injector with surge protection. Together these two devices offer maximum security and peace of mind.
Here’s what a typical use-case would be like. You have a mast with some antennas. And some switches on the ground. Put the GESP surge protector up there. It comes sealed inside a new and improved IP67 weatherproof enclosure. Your antennas are now safe during a lightning storm. Now add the GESP+POE-IN injector below the mast - to protect the switches and to power the antennas.
Don’t forget about the grounding wire! Secure it to the rackmount, mast, or any other structure that is connected to the ground. For maximum protection, you should use a surge protector on both ends of long cables. These small devices can make all the difference when it comes to lightning strikes or static build-up. The GESP units can usually absorb multiple impacts, but make sure to check their condition after each surge. For attachment of GESP units, we recommend using PVC zip ties. Just don’t make it too tight.You know what they say – hope for the best, prepare for the worst. This small investment can save lots of time and money, so why risk it? Grab a GESP & GESP+POE-IN and put your mind at ease!
СПЕЦИФИКАЦИЯ
MikroTik wAP LR8 kit - RBwAPR-2nD&R11e-LR8
wAP LR8 kit – an out-of-the-box solution to use LoRa® technology. This kit contains a pre-installed UDP packet forwarder to any public or private LoRa® servers and an outdoor weatherproof wireless access point with 2.4 GHz WLAN interface and Ethernet port that could be used as a backend.
This particular wAP form-factor has been tested in many other MikroTik products – it can deliver excellent and stable performance in almost any weather conditions. You can use the optional internal 2 dBi antenna or attach an external antenna. For extra network coverage we suggest adding MikroTik Antenna kit for LoRa®. wAP LR8 kit supports 863-870 MHz frequency, used in European Union, Russia, India etc. Functional and non-intrusive design, astonishing durability and great value – that is the wAP LR8 kit, the long-awaited solution for LoRa® technology for enthusiasts of any level.
